Outback Flat Roof Accessories
| Available Accessories |
| Outback Lights |  |
| Outback Ceiling Fan |  |
| Outback Rooflite |  |
Outback Flat Roof Design Information
Fixing Details
For Non-Cyclonic Areas
Two 12 x 20mm self drilling screws per pan at each support and two 3.2mm sealed aluminium rivets per pan at the back channel. If decking runs parallel to the back channel, secure to channel with rivets at maximum 200mm centres. All screws are to have neoprene washers.
For Cyclonic Areas
Three 12 x 20mm self drilling screws per pan at each support. For deck spans less than 3600mm, two self drilling screws per pan are to be used on fascia beam. Three 4.8mm sealed aluminium rivets per pan (or 150mm centres if sheets are parallel) to be used at the back channel. All screws are to have neoprene washers.
Roof Sheeting
Outback Deck
Polycarbonate Panel - Outback Rooflite
Structural Sections
Design Considerations
Gable/Curved Units Attached Between a Flat Unit & an Existing Structure
Gable/Curved Units which are attached between a Flat Unit (excluding pergolas) and an existing house, shall only be considered attached if the Gable/Curved Unit is attached to the existing house (C) for its full length (L) and the longest side of the combined unit (B) does not exceed twice the gable/curved length (L). The Flat Unit in this case can be considered attached. This style requires all coloumns to be embedded into footings.
Gable/Curved Units Attached to Flat Unit One or Both Sides
Gable/Curved Units which are attached one or both sides to Flat Units, (excluding pergolas) must be attached to an existing house for at least 75% of the gable/curved opening length (O) to be considered attached. Flat Unit/s must be deemed attached as detailed in the Flat Unit section below to allow the Gable/Curved Unit to be considered attached.
Gable/Curved Units are considered attached both sides if both Flat 1 and 2 comply with attachment rules for Flat Units as detailed below. Gable/Curved Units are considered attached one side if only one Flat Unit exists and it complies with the attachment rules for Flat Units as detailed below.
Flat Units
A Verandah, Patio, Carport or Pergola is deemed to be freestanding unless it is attached to an existing house (C) for at least 75% of the length of its shortest side (A), and its longest side (B) does not exceed twice the length of its shortest side.
Design Options
When designing an Outback, consideration should be given to both roof sheet direction, and the orientation of any openings and overhangs involved. These are often determined by appearence and drainage requirements. The following chart shows some of the normal options used, but contact Stratco if assistance is required.
| Outback Gable/Curved Verandah |
| Attached to Flat Unit One Side & Wall or Fascia One End |  |
| Attached Both Sides to Falt Unit & Wall or Fascia Opposite Side |  |
| Attached to Flat Unit Both Sides & Wall or Fascia One End |  |
Adapt the versatile Stratco Outback Flat Roof to suit your lifestyle
The Stratco Outback Flat Roof system is extremely versatile and can be configured to cover any area around the home.
It is ideal as a single unit or can be incorporated with a gable roof, curved roof, or pergola system for extra cover.
Available as a freestanding structure or attached to the home, it can be used as a carport, verandah or patio.
With the addition of Outback Rooflite, you can supply filtered light to the underside.
The beams can span up to 8.4 metres and are available in either 120mm or 150mm sizes.
Four configurations - Giving you choice and control
There are four Stratco Outback Flat Roof configurations to choose from:
- Type 1 Has a 4.5 metre maximum span and only requires an outside beam to support the structure. However most units use perimeter beams on all sides to provide the best appearance.
- Type 2 Is the same as Type 1, but also has an overhang at the front to increase the covered area to 5.4 metres.
- Type 3 Has support beams across its span so roofing sheets can run horizontally for a different appearance.
- Type 4 Has extra support beams and a purlin through the middle to give a span of 8.4 metres.
Simple to install - Ideal DIY project
Uncomplicated by design, the Stratco Outback Flat Roof is an ideal do it yourself project.
Everything is supplied as a complete package and all assembly instructions are provided.
Contact your nearest Stratco Home Improvement Store or Authorised Outback Dealer and let us show you the difference a Stratco Outback living solution can make to your home and lifestyle!
